-
Originally Posted by
jayjo96792
Is t400 from torax to much to shoot 1ml=400 mgs
Sent from my iPhone using Tapatalk
We always thought if it didn't hurt it wasn't 400mg .
Try 300mg/ml gear
Toraxx has exceptional gear and his carrier oil seemed to be Painfree . I would try in the Glutes first and if you have a good experience then you can try 1/2ml in shoulder before I did 1ml . I would use a 1ml 29G slinpin with 1/2 inch pin for shoulder . Make sure you have that 1/2 inch in deep .
Pull 1ml out of vial with 23G syringe . Set that down and pickup slinpin . Pull the plunger out with your teeth and don't set it down while holding the slin syringe . Pickup the 23G syringe and put the needle in the barrel of Slin syringe . Fill the slin syringe with 1ml oil slowly so you don't have a bubble. Still holding the slin syringe set the 23G syringe down . Take the plunger out of your mouth and ensert in the back of slin syringe. When you start putting plunger in syringe turn needle up in the air so bubble goes up to needle top . Will take a few seconds to press air bubble out .
I work near a counter so syringes can be set on the edge with needle not contacting any surface . Any needle that touches anything other than a sterile stopper on injection point is unusable.
This all sounds very difficult at first and is tricky . But after a few times you'll get better .
I lost .10 ml a few times before perfecting this method . I promise it will be so easy inserting pin that you'll never wanna meet another 25G barrel .
Regards
DWBO
Last edited by Dont wanna be old; 02-04-2017 at 02:31 AM.
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 Dislikes
----
-
That's gonna hurt anywhere you pin bro
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 Dislikes
----
-
Originally Posted by
Dont wanna be old
Toraxx has exceptional gear and his carrier oil seemed to be Painfree . I would try in the Glutes first and if you have a good experience then you can try 1/2ml in shoulder before I did 1ml . I would use a 1ml 29G slinpin with 1/2 inch pin for shoulder . Make sure you have that 1/2 inch in deep .
Pull 1ml out of vial with 23G syringe . Set that down and pickup slinpin . Pull the plunger out with your teeth and don't set it down while holding the slin syringe . Pickup the 23G syringe and put the needle in the barrel of Slin syringe . Fill the slin syringe with 1ml oil slowly so you don't have a bubble. Still holding the slin syringe set the 23G syringe down . Take the plunger out of your mouth and ensert in the back of slin syringe. When you start putting plunger in syringe turn needle up in the air so bubble goes up to needle top . Will take a few seconds to press air bubble out .
I work near a counter so syringes can be set on the edge with needle not contacting any surface . Any needle that touches anything other than a sterile stopper on injection point is unusable.
This all sounds very difficult at first and is tricky . But after a few times you'll get better .
I lost .10 ml a few times before perfecting this method . I promise it will be so easy inserting pin that you'll never wanna meet another 25G barrel .
Regards
DWBO
Been using t400 for a long time and only now it's starting to hurt every time I pin in shoulder,I'm talking that my arm is swollen for 4 days,the skin is super tight . Then goes back to normal Just been having a bad experience this time around and making me think that I should stop the t400
Sent from my iPhone using Tapatalk
----
-
Originally Posted by
SimpleAddar
That's gonna hurt anywhere you pin bro
Never had a problem before,only lately
Sent from my iPhone using Tapatalk
----
-
It's either high in ba, crystalizing from high milligram in the muscle, or could be the formula, (compounds)
Sent from my SM-G550T1 using Tapatalk
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 Dislikes
----
-
That's my understanding
Sent from my SM-G550T1 using Tapatalk
----
-
Your delts are probably full of scar tissue.
----
Bookmarks