Thread: Cloudy tren a

Ok so I have been warming up my tren A daily in a bathe of hot water that is dispensed from those 5 gallon water things for more than 3 to five mins .. .. I know the water comes out hot but not.too hot..

I heat up so it goes I'm smoother and I heard it helps with any pip ..

The only thing I've noticed is towards the end of my vial and after a few hot.bathes the oil becomes cloudy once cooled ..

Right after I let it.dip in water it clears up..

Dont know if it cause my apt.get cold during the day that it affects the oil or could it be the warming up.. process

Am I degrading it

Right is a fresh vial
Left is cloudy one
.

Sent from my SM-G950U using Tapatalk

The heat will cause oxidation but as long as the temps are not too high you shouldn't hurt it.

Have you ever tried just warming the gear up in the pin? Hold it between your fingers or something for a few mins to warm it up.

BPP

Originally Posted by bigpapapumpaf

The heat will cause oxidation but as long as the temps are not too high you shouldn't hurt it.

Have you ever tried just warming the gear up in the pin? Hold it between your fingers or something for a few mins to warm it up.

BPP

I used to warm up in the pin but found it easier just to dip the bottle in a hot bath..
The water temp isn't too hot..

Sent from my SM-G950U using Tapatalk

That's always been my concern with heating up the whole vial versus just the pin. Temperature fluctuations are never a good thing for chemicals. I'm sure it's just fine but for my own peace of mind I just run the pin under warm water for a minute.

Sent from my SM-N920V using Tapatalk

Originally Posted by bodean30

That's always been my concern with heating up the whole vial versus just the pin. Temperature fluctuations are never a good thing for chemicals. I'm sure it's just fine but for my own peace of mind I just run the pin under warm water for a minute.

Sent from my SM-N920V using Tapatalk

That's what imma do next time..

Sent from my SM-G950U using Tapatalk

Originally Posted by bodean30

That's always been my concern with heating up the whole vial versus just the pin. Temperature fluctuations are never a good thing for chemicals. I'm sure it's just fine but for my own peace of mind I just run the pin under warm water for a minute.

Sent from my SM-N920V using Tapatalk

Ya I used to put the whole bottle under water but now I just do it after I draw up and it is in the pin. So much easier and quicker to heat up the little oil that's in the pin instead of all the oil in bottle. I've heard different opinions on it but never got a direct answer say if your heating it up to much will it be damaged or lose its potency not under sink or bath water if anything would have to go past it's melting point if it were to get damage or lose it's potency and ive read and heard the hormone gets cooked out but there's no proof of that to my knowledge i might be wrong. You would think if it's heated up to much what about the BA and BB also wouldn't that get damaged or evaporate I know one of them wouldn't just don't know which one I'm not a brew guy or chemist. Sorry got off track a little. I think your good bro

Sent from my SM-J700T using Tapatalk

Originally Posted by Boxsquatter

Brothers and sista’s in my personal opinion and it’s mine. I think heating up gear is a waste of time and energy. Ok maybe if you are using a slin pin but what’s the sense. Does it really make that much of a difference. I have used 27, 30 g slin pins and I have use 18g harpoon’s when that’s all I had. So if heating it helps it flow better i don’t know. I don’t care what you put thru a 27g pin it’s going to flow slow. I use 25g all day every day biceps/calf’s /delts no problem and I don’t even feel them. Try them their is really no dif between 25-27g.

Always heat up my bottles on the heating pad prior.

The only time I have ever heated up any gear is when it’s crashed and I want to re-dissolve/suspend it.

Use a 25g pin and unheated gear and you’ll be fine.