-
Originally Posted by
bodean30
Agree with you there except you can actually save a bit of coin with blends from the right guy as opposed to buying the amount you need in separate vials. I saved quite a bit by running a blend this last cycle.
I also saved a lot by switching to Geico.
Sent from my SM-N920V using Tapatalk
Did your blends work as well as they would’ve if you pinned separately?
-
Post Thanks / Like - 1 Thanks, 1 Likes, 0 Dislikes
----
-
I guess what I’m getting to is I’ve read on here that some
folks didn’t like the blends as much as they liked pinning separately. I guess they were weaker.
----
-
Originally Posted by
macedog24
Its easy to adjust your dose with a blend.
Say its 100/100/100. Just an example.
But you wanna run 300 test/ 400 tren/ 500 mast.. Just making up something.
3pins at 1 ml is 300/300/300
Add .33 tren to each pin.
Add.65 mast to each pin.
Should be pretty good. So your pinning about 2ml , 3x a week and getting 300/400/500
If your pinning ed its easier.
.5ml x 6 pins/1pin@1/2ml for 6 days =300mg/300/300 you can adjust anything you want. However you want.
Long ester blends are even better/ easier.
Sent from my LG-H910 using Tapatalk
Now is the addition of tren and mast from another vial? Like a vial of mast and a vial of tren?
Sent from my iPhone using Tapatalk
“Live for something...or Die for nothing “
----
-
Originally Posted by
Bullseye Forever
Now is the addition of tren and mast from another vial? Like a vial of mast and a vial of tren?
Sent from my iPhone using Tapatalk
Yes
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 Dislikes
----
-
I blend to save pins and time.
I blend my Test E 300 and Deca 300, after they are already brewed and vialed. Both same recipe.
I take 5ml of each into one vial.
Heat oven to 190F.
Place vented vial in oven 20 minutes.
Remove with oven mitten, and while completely covered in mitten, shake for 5 minutes.
Remove from mitten, still warm.
Shake it here and there as it cools.
Each ml should be 150mg each.
I pin 2ml mon and thurs. (600mg each/wk.)
My vial gets a hot bath while I shower.
Water temp at sink is 110F.
Get out of shower and shake for 30 seconds.
Now, that is the only blend I make.
If I run Test higher, slin pin mire Test after main injection.
Slin pins are cheap.
Other compounds/blends may require different temps.
20180521_194943-800x600.jpg
Blend center, Test E left, Deca right
20180521_222121_1526956440538_1526956863355-800x600.jpg
Hot bath
20180522_205852-800x600.jpg
Last edited by Plate Smacker; 08-01-2018 at 02:47 AM.
"It's a lot of hard work, it's hard work that most people don't realize. I think the consistency of the hard work, is the hardest part." Dallas McCarver
-
Post Thanks / Like - 2 Thanks, 2 Likes, 0 Dislikes
----
-
Originally Posted by
bodean30
Agree with you there except you can actually save a bit of coin with blends from the right guy as opposed to buying the amount you need in separate vials. I saved quite a bit by running a blend this last cycle.
I also saved a lot by switching to Geico.
Sent from my SM-N920V using Tapatalk
Blends can save ya money.
I got ya a dollar. - YouTube
Sent from my LG-H910 using Tapatalk
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 Dislikes
----
-
I’m gonna pull the trigger on some blends.
----
-
Originally Posted by
RockDawg
Did your blends work as well as they would’ve if you pinned separately?
Sure did. Verified by bloods. Like I said, if you find the right guy they are worth it. I've seen shitty blends too. Also less to pin so that's a plus.
Sent from my SM-N920V using Tapatalk
-
Post Thanks / Like - 2 Thanks, 2 Likes, 0 Dislikes
----
-
Thanks for the reply brother
----
-
Personal preference entirely. I have to tell you, I am a control freak. As long as I know the shit I am on is dosed accurately, I want to be in control of how much of each compound I am getting. Depending on who has what, you may not be able to get that.
-
Post Thanks / Like - 1 Thanks, 2 Likes, 0 Dislikes
----
Bookmarks