-
If you're worried about uneven distribution of any of the compounds, just gently heat the vial for about 5 minutes.
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 Dislikes
----
-
Even if the compounds youre mixing were the same ester weight and carrier I dont see the benefit to combining into one vial. Vials arent exactly bulky or inconvenient
----
-
Originally Posted by
ShortnWide
There's two ways of thought on this subject.
1. Most people believe that mixing oils is fine. Two finished products in one pin will still be two separate compounds that enter the body and do their appropriate job unchanged.
2. Some people believe that mixing AAS will harm the compounds and make them less affective. Each compound should be shot in a dif body part and the bodypart should be aloud 5-7 days from next inject to aloe all absorption of from previous inject.
I def am a person who believes in mix my gear. Once a compound is a finished product, nothing but high heat and additives will change that.
But I def would not mix 2 different vials of compounds in to 1 bottle. There will be difffernet weights and makeups that will not mix exactly the amount a persons going to get when measuring with a pin and 2 seprate vials.
Agreed!
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 Dislikes
----
-
I have been on TRT for 3 years. I have just ordered Mast E and started using it about 2 weeks ago. When I pin, there is no pain (at all). It is a slow push and a good massage after. Lately after mixing the Test and Mast in the same syringe, there is no pain immediately after, however, the next day there is major soreness around pin sight. Is there something I am doing wrong or should know? I have never done AAS and so I am learning. Thanks!!!
----
-
Originally Posted by
KPack
I have been on TRT for 3 years. I have just ordered Mast E and started using it about 2 weeks ago. When I pin, there is no pain (at all). It is a slow push and a good massage after. Lately after mixing the Test and Mast in the same syringe, there is no pain immediately after, however, the next day there is major soreness around pin sight. Is there something I am doing wrong or should know? I have never done AAS and so I am learning. Thanks!!!
When I shoot two cc in separate pins I shoot one cc in one quad and one cc in the other however, if I mix them in one syringe I shoot it in the same leg which obviously causes more pip so if you were shooting both in the same leg already and just mixed it then the problem is something else (probably) if you started shooting an extra cc that will cause pip. If you want to you can hear water up in the microwave in a measuring cup for 2 min and then submerged the vial in the heated water about half way up the vial maybe a little more. It's not hot enough to damage it and imo it's better then heating the syringe and it definitely makes it easier to shoot. Good luck brother
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 Dislikes
----
-
I always mix my oils and have never had an issue.
----
-
Originally Posted by
masteratarms
When I shoot two cc in separate pins I shoot one cc in one quad and one cc in the other however, if I mix them in one syringe I shoot it in the same leg which obviously causes more pip so if you were shooting both in the same leg already and just mixed it then the problem is something else (probably) if you started shooting an extra cc that will cause pip. If you want to you can hear water up in the microwave in a measuring cup for 2 min and then submerged the vial in the heated water about half way up the vial maybe a little more. It's not hot enough to damage it and imo it's better then heating the syringe and it definitely makes it easier to shoot. Good luck brother
Right on Brother! Will try the heat.
Sent from my SM-N920T using Tapatalk
----
-
Never had problem mixing long esters in same pin. Short esters gives me pip and sometimes it can be major.
----
Bookmarks