masteron E crashes.. what's wrong???

[underpsi]

first attempt at brewing.. tried masteron E at 200/ml and when it cools/stored for more than one day it crashes.. put it in a bath of warm water and it reconstitutes itself fine. no crystals at all.. here's recipe i used.
10g powder
33.5 Grapeseed Oil (GSO)
1.5ml BA (3%)
7.5ml BB (15%)

any suggestions? thank you

[Bane]

http://uploads.tapatalk-cdn.com/20160423/80bff5e1389847ea1ac1af550d7448cb.jpg
I used bass killer and this is what I got.

[underpsi]

thank you....

[Bane]

You're welcome. Hope it works out for u.

[underpsi]

used the calculator ... did 1/4 of what you put in
10g
30.5 gso
1ba
9 bb
still same !!! not really separating but cloudy when cold... when i put in warm water for 2-3 min looks perfect again... go figure. thinking maybe was sent mast prop not eth.

[Bane]

used the calculator ... did 1/4 of what you put in
10g
30.5 gso
1ba
9 bb
still same !!! not really separating but cloudy when cold... when i put in warm water for 2-3 min looks perfect again... go figure. thinking maybe was sent mast prop not eth.
Sorry to hear it didn't work. The calc is usually gtg. Maybe there is an old pro in here that will see this and help.

[Bane]

used the calculator ... did 1/4 of what you put in
10g
30.5 gso
1ba
9 bb
still same !!! not really separating but cloudy when cold... when i put in warm water for 2-3 min looks perfect again... go figure. thinking maybe was sent mast prop not eth.
Not positive but the amount of mast per ml may be to high. I have a list and the highest they went was 166mg/ml. So maybe just to high concentration. Like I said I don't really know for sure. Someone else on here surely knows.

[ski748134]

I don't get the ? The calculator is not hormone specific as far as I know

[Bane]

It has a weight displacement at the bottom Ski. It has a few compounds under the weight list and mast is 1. Check it out and see what u think. It was basskiller and it's right below the chart

[2stones]

Had the same problem .I raised the heat a little higher and cooked a little longer. Presto good product.

[underpsi]

long time since i posted this... just wanted to update in case someone did a search etc.
found i had masteron PROP! not E ! was actually MY mix up.. of coarse prop doesn't hold well at 200mg . dropped it to 150 .... it got better..... then next time to 100 mg.. held fine. realized then that i might have made mistake. looked up and sure as hell...
just ordered mast E and of coarse holds fine at 200 same recipe

[Woods]

Add BB% 15 is to low . At least 18 just in my opinion. I didn't read ur last post sorry with prop I would go 20%.

[ski748134]

Only thing that u need to upper the BB is no esters everything else I have never gone higher then 18℅

[TEPENEX]

YES its prop if its not staying in solution at the mg/ml.
I would just drop it to 100mg/ml and you WILL find it stays in suspension.

p.s. An emulsion works better : ) look into it!

[underpsi]

thanks guys.. prop long gone. finally figured it out after some time. dropping to 150mg per then to 100 mg /ml and it would stay in suspension. went back and reviewed my emails and found i had ordered prop by accident.. kept trying to get it to hold at 200 not knowing.. thanks

[ILIFT2LIVE]

Ya 18-20% will hold better also maybe look at your temp maybe not hot enoigh to break down the hormone so it stays in a soluable state


Sent from my iPhone using Tapatalk Pro