Redis
03-30-2012, 09:15 PM
I just finished my first attempt at brewing. I did a finaplix-h conversion for four grams of tren at 40ml, so 100mg/ml. I read everything I could, but used mainly this guide from basskiller's website. http://www.basskilleronline.com/steroids-finaplix-tren-conversion.shtml
So, here's my log of how it went. I would appreciate any input or tips from experienced brewers, thanks!
1. I poked the pellets out of the cartridges with a paperclip. Some didn't want to budge, but using two paperclips fixed that.
2. Stuck the pellets in a unsealed 100ml vial. I wish I had used something else and will in the future. Thinking flask or a beaker. It was too hard to stir because of the tiny hole.
3. Added .8ml BA, 7.2ml BB, and 28ml of cotton seed oil to the crushed pellets and saved 2ml of cottonseed oil in a syringe. On a side note, was using 10ml syringes and a mix of 18g needles as well as 25g for venting. The final sealed, sterile vial was a 50ml one.
4. I let the pellets sit over night, but to be honest, not a whole lot happened, so I brought some water to a boil, dropped the temp, and then let the vial of pellets and BB/BA/CO sit there. That got it going. The stopper popped off and made the water around the vial oily. Whoops! Will leave the stopper off or just use a needle to vent next time. I occasionally put the stopper back on and just shook everything up.
5. I decided to skip the coffee filtration.
6. I then took my sterile, sealed vial, stuck the 25g and 18g needles in, then added the .45 whatman to the 18g and back loaded the dissolved stuff into a 10ml syringe, which I attached to the top of the whatman. It took about four syringe refills to filter it all. At the end, I changed the whatman at a stupid time and lost about 2ml of product, but better then than earlier when all the good shit was being filtered.
7. I pushed the final 2ml of oil through the whatman.
Here's a pic of my final product.
551
I'm going to try a few different things. I've got 8 carts left to experiment with.
1. not crushing the pellets
2. adding only the BB/BA to the pellets, add the oil after they dissolve.
Like I said, I'm open to any criticism, advice, etc. I'm just looking to learn and improve the process. Thanks.
So, here's my log of how it went. I would appreciate any input or tips from experienced brewers, thanks!
1. I poked the pellets out of the cartridges with a paperclip. Some didn't want to budge, but using two paperclips fixed that.
2. Stuck the pellets in a unsealed 100ml vial. I wish I had used something else and will in the future. Thinking flask or a beaker. It was too hard to stir because of the tiny hole.
3. Added .8ml BA, 7.2ml BB, and 28ml of cotton seed oil to the crushed pellets and saved 2ml of cottonseed oil in a syringe. On a side note, was using 10ml syringes and a mix of 18g needles as well as 25g for venting. The final sealed, sterile vial was a 50ml one.
4. I let the pellets sit over night, but to be honest, not a whole lot happened, so I brought some water to a boil, dropped the temp, and then let the vial of pellets and BB/BA/CO sit there. That got it going. The stopper popped off and made the water around the vial oily. Whoops! Will leave the stopper off or just use a needle to vent next time. I occasionally put the stopper back on and just shook everything up.
5. I decided to skip the coffee filtration.
6. I then took my sterile, sealed vial, stuck the 25g and 18g needles in, then added the .45 whatman to the 18g and back loaded the dissolved stuff into a 10ml syringe, which I attached to the top of the whatman. It took about four syringe refills to filter it all. At the end, I changed the whatman at a stupid time and lost about 2ml of product, but better then than earlier when all the good shit was being filtered.
7. I pushed the final 2ml of oil through the whatman.
Here's a pic of my final product.
551
I'm going to try a few different things. I've got 8 carts left to experiment with.
1. not crushing the pellets
2. adding only the BB/BA to the pellets, add the oil after they dissolve.
Like I said, I'm open to any criticism, advice, etc. I'm just looking to learn and improve the process. Thanks.