EQ recipes and procedures

[JTH]

How do you guys brew your EQ? I’ve seen basskiller’s version; however, I’d rather add my bb and ba when the brew begins to cool (less than 115*F).

Also, what’s a typical amount of EQ per ml? 200? 300 mg/ml?

any help would be greatly appreciated!

[Steele7]

How do you guys brew your EQ? I’ve seen basskiller’s version; however, I’d rather add my bb and ba when the brew begins to cool (less than 115*F).

Also, what’s a typical amount of EQ per ml? 200? 300 mg/ml?

any help would be greatly appreciated!Really????????

Sent from my moto e5 play using Tapatalk

[Steele7]

How do you guys brew your EQ? I’ve seen basskiller’s version; however, I’d rather add my bb and ba when the brew begins to cool (less than 115*F).

Also, what’s a typical amount of EQ per ml? 200? 300 mg/ml?

any help would be greatly appreciated!200

Sent from my moto e5 play using Tapatalk

[JTH]

200

Sent from my moto e5 play using Tapatalk


Ive seen numerous posts of 200 and 300. Just curious as to what people are using.

[JTH]

For 200mg/ml, would 1%BA and 10%BB suffice, as far as ratios?

[balin]

Why do you add your solvents after you already have it in a solution?

[JTH]

I heat most solutions (except tren). Then, as they come down in heat, I’ll add my bb and ba.

[THX]

300mg/ml.

[balin]

I heat most solutions (except tren). Then, as they come down in heat, I’ll add my bb and ba.

Yes I saw that in your earlier post. I was asking why you add the BA and BB in after it is in solution since most people use it to dissolve the powder to make it easier to put into solution.

[JTH]

A guy I consider a mentor does it (Rmewrench). If you add your solvents then heat the mixture then your solvents will evaporate thus nullifying the reason of adding them to begin with.

[JTH]

Thank you THX!

[THX]

For 200mg/ml, would 1%BA and 10%BB suffice, as far as ratios?

You probably don't even need to add BB at 200mg/ml

I've made 300mg/ml with 2%BA and 15% BB. You can probably make 300mg/ml with only 1%BA and 10% BB. I live in a cold climate so I'm not taking any chances. No need to heat it up that much.

[JTH]

You probably don't even need to add BB at 200mg/ml

I've made 300mg/ml with 2%BA and 15% BB. You can probably make 300mg/ml with only 1%BA and 10% BB. I live in a cold climate so I'm not taking any chances. No need to heat it up that much.


Thank you, sir!

[balin]

I have made EQ at 400mg/ml using a 2/20 and probably could have used less. And the pip was ok as I mix and thin it with other AS. Just depends on how thick you want to make it.

[JTH]

I have made EQ at 400mg/ml using a 2/20 and probably could have used less. And the pip was ok as I mix and thin it with other AS. Just depends on how thick you want to make it.

Thank you, sir!

[Enigma]

Eq at 200mg/ml is always 1.5%/3% BA/BB for me. Never had any crash in any climate above freezing.

Btw, your solvents won’t evaporate during the brewing process. They are too involved in the whole of the solution to exhibit the same properties that they do on their own. BA doesn’t exactly evaporate at a noticible rate anyway.
Putting everything in the batch on your stirplate ensures a well blended product.

[balin]

The evaporation/boiling point of BA and BB is about 200 and 300 degrees as I remember.

[JTH]

Eq at 200mg/ml is always 1.5%/3% BA/BB for me. Never had any crash in any climate above freezing.

Btw, your solvents won’t evaporate during the brewing process. They are too involved in the whole of the solution to exhibit the same properties that they do on their own. BA doesn’t exactly evaporate at a noticible rate anyway.
Putting everything in the batch on your stirplate ensures a well blended product.


Thank you! You’re a wealth of knowledge, sir!

[JTH]

The evaporation/boiling point of BA and BB is about 200 and 300 degrees as I remember.
Good to know! Ty!

[BEASTZ6]

I brew EQ at 250 mg/ml. 2% BA and 15% BB.

[JTH]

I brew EQ at 250 mg/ml. 2% BA and 15% BB.

Thank you!