How to build a syringe press

[Yellowninja]

I built a new syringe filter press out of wood it works even better then the original stainless steel one I built
I posted step by step directions here https://brotherhoodofpain.com/anabolic-hormones-com/61017-build-simple-syringe-press.html if anyone is interested in building one.
It costs under $20 and took less then 2 hours to build it

38060

38061

38062

[Enigma]

Again, you should be venting with asyringe filter. Even the cheap, non sterile eBay ones would be an improvement over open to the atmosphere.

[Yellowninja]

Again, you should be venting with asyringe filter. Even the cheap, non sterile eBay ones would be an improvement over open to the atmosphere.

I just ordered some they will be here for my next brew

[Yellowninja]

Again, you should be venting with asyringe filter. Even the cheap, non sterile eBay ones would be an improvement over open to the atmosphere.

Filter material shouldn't matter because only air should be passing through correct?

[Plate Smacker]

A pvc pipe that fits over plunger thumb contact, secured to wooden 3×1 backing using pvc fastener,...
Inside pvc pipe, insert slightly longer wood dowel or preferred metal rod with threads that can accept flange, extending through pvc pipe to make contact with flat thumb part of plunger.
On top of flange, place weight.

[Enigma]

Filter material shouldn't matter because only air should be passing through correct?
Yes. You can even use larger sized but if you can get .22, why not?
I would pierce with venting needle with filter attached first, then your syringe.

[Yellowninja]

Yes. You can even use larger sized but if you can get .22, why not?
I would pierce with venting needle with filter attached first, then your syringe.

Yes I'm ordering 13mm .22 just wondering if it needed to be pvdf of if it's ok to use pes or nylon cause the pes and nylon are almost half the price of the pvdf.

[Devilman65]

That looks cool a/f.Wish I could home brew

[jet2000]

Thank you, that's a genius idea

[THX]

Yellowninja you're the McGyver of this forum :) Love this contraption that you made.

[Yellowninja]

Yellowninja you're the McGyver of this forum :) Love this contraption that you made.

Thanks. It makes life alot easier on small brews, forearms no longer burning and I can work on other things while its filtering. I will be taking enigma's advice and using some 13mm .22 filters on the vent needle next brew. Going to try my hand at some mast-e and tren-e. Also thinking I'm going to do a blend of 200mg mast-e,100mg test-e, 75mg deca/ml it will be perfect for my next cycle. Think it will hold at ba 2% bb 20% in mct oil?

[Oldskool]

I built a new syringe filter press out of wood it works even better then the original stainless steel one I built
I posted step by step directions here https://brotherhoodofpain.com/anabolic-hormones-com/61017-build-simple-syringe-press.html if anyone is interested in building one.
It costs under $20 and took less then 2 hours to build it

38060

38061

38062What are the medical supplies u use for this set up?

A 20ml syringe?

I was wanting to use a 60 ml syringe due to the fact once I've tested out a recipe my doing only 10 ml and waiting a couple weeks to see if it holds I'm going to do 50 ml batches to fill the 50 ml sterile vials I have.

Will a 60 ml syringe fit in this set up?

Will a 50 ml vial be able to fit at the bottom?

Sent from my SM-G965U using Tapatalk

[Yellowninja]

What are the medical supplies u use for this set up?

A 20ml syringe?

I was wanting to use a 60 ml syringe due to the fact once I've tested out a recipe my doing only 10 ml and waiting a couple weeks to see if it holds I'm going to do 50 ml batches to fill the 50 ml sterile vials I have.

Will a 60 ml syringe fit in this set up?

Will a 50 ml vial be able to fit at the bottom?

Sent from my SM-G965U using Tapatalk

I'm not sure if a 60ml will fit I've only used a 20ml syringe. I know it will work with both 10ml and 20ml viles.

[Oldskool]

I'm not sure if a 60ml will fit I've only used a 20ml syringe. I know it will work with both 10ml and 20ml viles.That's what I figured.

That's ok. I can drill a hole in the bottom piece if wood the size of the 50 ml vial.

The vial will drop down into the hole making it fit.

Whenever I do 20ml vials I can just put down a thin piece of sheet metal to cover the hole.

This is just gonna be a cheap prototype anyway.

Maybe I can just cut extra pieces of removable wood to put down when I use the 60 ml syringe to account for the increased size/length.

Experimenting and modifying it will be half the fun of it anyway.

Sent from my SM-G965U using Tapatalk

[Yellowninja]

Sounds good

[musclemac]

Incredible device!! I simply buy brand new call gun, get a washer to put between 60ml syringe and syringe filter-slide 60ml syringe into caulk gun so that when plat presses down on back of syringe it places the washer on the inside of point of calk gun so pressure applies there and non is syringe filter..works amazing however you can only draw up about 45 MLS of brew so they extended plunger and all fits. Save hands and with patients can brew/bottle alot even with .22s syringe filters.

[Raw]

Your step by step on the first post seems to be a dead link now Yellow.

[Yellowninja]

Try this link
How to build a simple syringe press (https://brotherhood.is/anabolic-hormones/61017-build-simple-syringe-press.html)

[Raw]

Try this link
How to build a simple syringe press (https://brotherhood.is/anabolic-hormones/61017-build-simple-syringe-press.html)


Thank you.

[bobhead]

Nice!!

[Jimjimqwerty]

Creative