Pins and syringes 1st cycle

[Brick Crusher]

I'm going to start my first test-e 12 wk. What pins and syringes is needed?

Sent from my SM-G965U using Tapatalk

[samgraves82]

I'm going to start my first test-e 12 wk. What pins and syringes is needed?

Sent from my SM-G965U using Tapatalk1in × 25g

[Sqwuidd]

I'm going to start my first test-e 12 wk. What pins and syringes is needed?

Sent from my SM-G965U using Tapatalk

How lean are you? I would recommend 1 inch pins if your a little beefy

I use 1/2 inch 29gauge
And hit it where I’m the leanest


Sent from my iPhone using Tapatalk

[socalmk6gti]

20-21g to draw. Dont go 18g as too many UGL's use crappy stoppers that shred. Don't go smaller than a 21g for drawing.

Make sure to have same gauge, about 25g, with 1" and 1.5" for pinning. 1" for delts, chest, etc... and 1.5" for quads, glutes etc.

Sent from my Pixel 2 XL using Tapatalk

[chadmack282]

What's your bf%

[joko123]

First cycle 1inch is pretty standard everywhere , personal preference is 23g


Sent from my iPhone using Tapatalk

[Ranger15]

Most labs these days use such thin oil that there’s really no need for a large gauge to draw with. I like use same gauge that I pin with always swapping out the one I used to draw for a new one to pin . I always use 25 gauge 5/8 BD luer lok

[thebear]

Get a vial adapter. You won’t need 20g or 21g draw needles anymore. I use 3cc syringes with 25g quad or VG. Like butter.


Sent from my iPhone using Tapatalk

[Sqwuidd]

I draw with 23g pin into 3 cc tube

I then backload a 28g 1/2 inch slin pin and inject IM (usually into VG or delt)

If I am doing more than 1 cc I backload multiple slin pins and inject in multiple places

Smooth flow
No force needed it just glides in
I always use the EasyTouch slins been doing this for years w no issues — only time I had an issue is I pinned 3cc short esters into VG and didn’t 1) slightly vary injection site and 2) one of these injects was subq accidentally bc I was rushing

^^this is the way I always pin
I buy like 400 of these slins at a time and they last me for few months (I use them for peptides , GH and oils )

Shit is amazing — no need for a huge harpoon scarring my tissue daily


Sent from my iPhone using Tapatalk

[Big ragu]

20gx1” to draw, 25x1” to pin. I pin delts and glutes. Right now I draw with a 1cc syringe, mix in a 3cc.

[Brick Crusher]

What's your bf%10%

Sent from my SM-G965U using Tapatalk

[Brick Crusher]

Also how many of them I need for this cycle?

Sent from my SM-G965U using Tapatalk

[sa355355]

Also how many of them I need for this cycle?

Sent from my SM-G965U using Tapatalk

# of times you plan to inject per week multiplied by the # of weeks in your cycle


So if you plan to inject twice a week for 12 weeks you need a minimum of 24 syringes w/ needles

Just buy a box of 100 and you will be fine






Sent from my iPhone using Tapatalk

[Auschemlab]

Always 1inch needles 25g, that’s the common practice in the bodybuilding community (well steroid community)