400 mg/mL Test Cyp?

[Leemm]

Anyone have any luck making 400 mg/mL test cyp? If so, what recipe did you use?

[Yellowninja]

Test-c no I don't think its possible its hard enough to get it to hold at 250mg/ml
Test-e yes it will hold easily at 2%ba and 20% bb

[maxmuscle1]

Test-c no I don't think its possible its hard enough to get it to hold at 250mg/ml
Test-e yes it will hold easily at 2%ba and 20% bb

Ready to see all the crystallized cyp tds! Lol

Max
#winterishere

[LiftHeavy]

Test-c no I don't think its possible its hard enough to get it to hold at 250mg/ml
Test-e yes it will hold easily at 2%ba and 20% bb

Damn, 20 percent bb gotta have some bite. Strange Test Cyp won't hold, its only 1 carbon heavier.

[Leemm]

Made 400mg/ml test cyp in pure ethyl oleate with 1% benzyl alcohol. Has been holding for over a week at 63 degrees f. I have not injected any yet, but I do well with ethyl oleate. Will update after injecting.

[Leemm]

Is there an easy way to predict solubilities? I know for oral suspensions you match your AAS molecular weight to the PEG weight, but there does not seem to be a correlation like that with oil injectables. Any thoughts?

[Zerocool69]

Test-c no I don't think its possible its hard enough to get it to hold at 250mg/ml
Test-e yes it will hold easily at 2%ba and 20% bb

Looking in the recipe section, it looks like Test-C and the rest are all done with sesame seed oil. I use MCT oil, would I use the same volume of MCT oil, BA & BB as listed for the recipe with sesame seed oil?

If not, what would be a good recipe using the MCT oil, ect... for 20 mL of Test C at 250 or even 200?

Thanks in advance and sorry if I have this question posted in the wrong section.


Sent from my iPhone using Tapatalk

[ski748134]

Damn, 20 percent bb gotta have some bite. Strange Test Cyp won't hold, its only 1 carbon heavier.

bb at 20% i have no bite issues with using a higher bb is way better then eo or different solvents

[Alan0160]

There is a sponsor on this board that offers Test-C at 400mg/ml. According to the above responses,
it would seem very unlikely that the label claim is being met.

[Yellowninja]

bb at 20% i have no bite issues with using a higher bb is way better then eo or different solvents

I agree with this completely. I've brewed test-e 300mg/ml with 10% bb and 20% bb and couldn't tell a difference when injecting

[ski748134]

I agree with this completely. I've brewed test-e 300mg/ml with 10% bb and 20% bb and couldn't tell a difference when injecting

i cant either i think that messing around with bb is a great way to brew so eo and solvents dont have to be used i have gone up to 22% bb no issues

[SloppyJ]

I've had BB as high as 35% on accident and never had any sort of PIP. It's not ideal but better than other solvents as others have stated. I purposely keep my BB% high so I don't have to worry about it crashing.

The only test I would try at 400mg/ml is test e. Cyp absolutely sucks just going to 250mg but there should be no problem with test e at 400 around 20% BB. As a standard, I make test e at 300 with 18% BB and I'm sure I could go down to 10% or lower.

Test iso had a little harder of a time going into solution but a little bit of heat and some mixing and it went in fine and I haven't seen any indication of crashing at 300mg/ml and 20% BB.

Prop at 150 all day long.

[Caustic Charm]

I've had BB as high as 35% on accident and never had any sort of PIP. It's not ideal but better than other solvents as others have stated. I purposely keep my BB% high so I don't have to worry about it crashing.

The only test I would try at 400mg/ml is test e. Cyp absolutely sucks just going to 250mg but there should be no problem with test e at 400 around 20% BB. As a standard, I make test e at 300 with 18% BB and I'm sure I could go down to 10% or lower.

Test iso had a little harder of a time going into solution but a little bit of heat and some mixing and it went in fine and I haven't seen any indication of crashing at 300mg/ml and 20% BB.

Prop at 150 all day long.

I’ve made a lot of prop 200, holds great at 21-23% BB. It stings but it’s worth it if you want to go high dose with test but with short ester. 1cc EOD gives you 750mg a week.


Sent from my iPhone using Tapatalk

[Caustic Charm]

And to add to my above statement, literally no need for 400mg test cyp. 5 days in between shots and that one shot hurts like fuckall. My 2 cents on the subject.


Sent from my iPhone using Tapatalk

[maxmuscle1]

I've had BB as high as 35% on accident and never had any sort of PIP. It's not ideal but better than other solvents as others have stated. I purposely keep my BB% high so I don't have to worry about it crashing.

The only test I would try at 400mg/ml is test e. Cyp absolutely sucks just going to 250mg but there should be no problem with test e at 400 around 20% BB. As a standard, I make test e at 300 with 18% BB and I'm sure I could go down to 10% or lower.

Test iso had a little harder of a time going into solution but a little bit of heat and some mixing and it went in fine and I haven't seen any indication of crashing at 300mg/ml and 20% BB.

Prop at 150 all day long.

That is so rad!!300mg/ml of Tear Iso !!! [emoji91][emoji95][emoji95]

Max [emoji123]

[Jaxz]

If you want 400 why just do a blend of e and c 200/200. Not that much difference in the esters

[Leemm]

Update. Have used the 400 mg/ml Test cyp in pure EO as .5 ml SubQ injections a few times. Stomach fat. Have not had pain or residual nodules a week out from pins.

Do you think test base would hold at the same concentration?