Anyway to make oil come out syringe easier?

[Yeh itsahomicide]

I’m using 23 g 1 inch. I’ve never had much issue getting the oil out during injection but the new company I’m using the oil is thick. Is there a way to make the oil come out easier because I’m bruising my thumb just trying to inject.

[*XXL]

Damn! I draw with that but use 29g to pin. Patience I guess.


EXO-GEN [emoji1022]
Beyond Human Genetics
List: [email protected]

[pharmahgh]

23g is a HARPOON BROTHER WHAT? lol Should not have any issues pushing oil through that massive thing... It isn't supposed to just inject like a saline injection. Any oil will take a bit of time, but if its taking any longer than 10 seconds per 1ml of oil then I have no idea what could be wrong?
I will usually run mine under some hot water for 30 seconds prior to injection, I feel way less pip in general that way and it moves through the needle easier. But I backload 30g 1/2 inch slin pins for my shots. It takes a bit of patience but using the smaller gauges is worth it in my mind.

[rrambo1]

I draw and inject using 28gauge slin.... yes it takes a little while to draw... I don't care...

[hamsandwich]

I use 23ga and every pin is super quick. How many MLs are you injecting and what product?

[mirahan]

Scar tissue building up from using the same area over and over will make my oils hard to inject.
I stick, then back off a 1/4" inch. Then it usually flows in.
Heating your oil helps also.
Also rotate your injection sites. Quads and Glutes are good for me. Some guys throw Delts in.
If you feel a lump in your muscle, don't try to inject into it.
Either go to the next muscle in your rotation, or if you are like me and use short esters, you may have all you damn muscles full of depots.
In that case try to move around the muscle to miss the 'lump'

[bigdaddy6900]

Scar tissue building up from using the same area over and over will make my oils hard to inject.
I stick, then back off a 1/4" inch. Then it usually flows in.
Heating your oil helps also.
Also rotate your injection sites. Quads and Glutes are good for me. Some guys throw Delts in.
If you feel a lump in your muscle, don't try to inject into it.
Either go to the next muscle in your rotation, or if you are like me and use short esters, you may have all you damn muscles full of depots.
In that case try to move around the muscle to miss the 'lump'

I draw with 18 use either 23 or 27 depending on muscle 23 Is as big as I’d go 22 gives me bruises every time


Sent from my iPhone using Tapatalk

[Mr.Beefy]

After drawing in with the syringe..I usually wrap it in a heating pad for a about 3 to 5 mins on low. To me it makes the oil have less viscosity to it. I tend to use a 25g (in the past) but I usually use a 23g.

[Zitbak]

I'm using 25g and it takes a good amount of time (30+ seconds) to pin 1mL. I have to push extremely hard. Not sure if that's a typical time to push 1mL of Test through glutes.

[Mr.Beefy]

Viscosity is a measure of an oil's resistance to flow. It decreases (thins) with increasing temperature and increases (or thickens) with decreased temperature. ... This property is referred to as the oil's viscosity index or VI. The higher the VI of an oil, the less its viscosity is altered by temperature changes.

[RIPPED FREAK]

I’m using 23 g 1 inch. I’ve never had much issue getting the oil out during injection but the new company I’m using the oil is thick. Is there a way to make the oil come out easier because I’m bruising my thumb just trying to inject.

You should use a brand with oil less tick because 23g is already very large needle to inject . I use 25g easy and sometimes 27g . You can heat the oil but if you heat to much you burn yourself . And the oil you using is not normal so thick that dont go well on 23g