-
Brewing for second time
Hi guys,
Second time brewing and i wanted to increase the concentration a little this time. My first brew i successfully made test e @ 250mg/ml, Boldenone @300mg/ml and Tren A @100mg/ml using MCT Oil
Second brew I plan to use the following:
Test E @ 300mg/ml 15%BB 1%BA
Boldenone @ 400mg/ml 15%BB 1%BA
Tren E @200mg/ml 15%BB 1%BA
Test Prop @ 100mg/ml 18%BB 1%BA
My question is do i need to alter the BB and BA content for any of these and also will the Boldenone be painful @ 400mg/ml?
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 Dislikes
----
-
I'm not master brewer been reading and researching a shit ton on it but at that level you might have to swap out some oil for guaiacol.
Sent from my iPhone using Tapatalk
----
-
Originally Posted by
Kobra
Hi guys,
Second time brewing and i wanted to increase the concentration a little this time. My first brew i successfully made test e @ 250mg/ml, Boldenone @300mg/ml and Tren A @100mg/ml using MCT Oil
Second brew I plan to use the following:
Test E @ 300mg/ml 15%BB 1%BA
Boldenone @ 400mg/ml 15%BB 1%BA
Tren E @200mg/ml 15%BB 1%BA
Test Prop @ 100mg/ml 18%BB 1%BA
My question is do i need to alter the BB and BA content for any of these and also will the Boldenone be painful @ 400mg/ml?
If you don't mind me asking will percentage BB and BA did you use in the first batch that you made?
Sent from my SM-G935V using Tapatalk
----
-
Boldenone @ 400mg/ml is fine,i hear some people even use 800mg/ml.
----
-
Originally Posted by
Yukilmc
Boldenone @ 400mg/ml is fine,i hear some people even use 800mg/ml.
So in order to make a higher mg of any product, you would have to add more ba and BB or just one or the other?
Sent from my SM-G935V using Tapatalk
----
-
not like that.Exceeding a certain range will cause pain.BA don't exceed 5%,2% is common use,it's mainly used for keep stuff bacteriostatic and sterile;BB is at 15%-20% for most people with nearly painless.Anyway,it's painless at low level.
----
-
Test E & boldenone were 18%BB and 2% BA. Tren A was 20%BB and 2% BA. All are still holding and havent crashed.
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 Dislikes
----
-
Originally Posted by
Kobra
Test E & boldenone were 18%BB and 2% BA. Tren A was 20%BB and 2% BA. All are still holding and havent crashed.
Test E and EQ do not need BB to be brewed. Pharm grade comes with 2% BA. BA is just a preservative, it keeps your solution sterile after all is said and done. EQ comes in liquid already, 400mg/ml will be smooth. To much BB in your gear will cause tren cough. So dont use it unless absolutley needed. Also, PIP comes from carbolic acid, is a chemical used in the manufacturing process of the raw. You can make test e @400mg/ml without BB and itll hold and be smooth.
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 Dislikes
----
-
Originally Posted by
Rmewrench
Test E and EQ do not need BB to be brewed. Pharm grade comes with 2% BA. BA is just a preservative, it keeps your solution sterile after all is said and done. EQ comes in liquid already, 400mg/ml will be smooth. To much BB in your gear will cause tren cough. So dont use it unless absolutley needed. Also, PIP comes from carbolic acid, is a chemical used in the manufacturing process of the raw. You can make test e @400mg/ml without BB and itll hold and be smooth.
KOBRA,
The above by rmewrench is spot on.
I would like to add that using Ethyl Oleate helps with pain as well, a small % of people are allergic to it but helps a great deal with PIP. A good basic ratio is to use a 1/3 of your total oil as EO. MAKES a big difference.
* Also using a THICK oil like castor oil will help, it will take longer to filter but it can help as well.
try 1/3 of castor,1/3 of EO and a 1/3 of whatever you usually use mct is decent.
Last edited by TEPENEX; 04-26-2017 at 02:58 PM.
----
-
Originally Posted by
littlefrank
I'm not master brewer been reading and researching a shit ton on it but at that level you might have to swap out some oil for guaiacol.
Sent from my iPhone using Tapatalk
Yeah I meant EO here not guaiacol
----
Bookmarks