-
First time brewing
Looking to attempt a brew for the first time looking for an easy Test Cyp recipe that is tried and true the less PIP the better.
-
Post Thanks / Like - 1 Thanks, 1 Likes, 0 Dislikes
----
-
First time brewing
Plenty of recipes in the home brew chem section bro. Just do some reading. Not many compounds will give you any trouble unless you're doing a stupid high concentration. Most brews are really straight forward.
Sent from my iPhone using Tapatalk
Last edited by Droid1988; 06-14-2018 at 04:43 PM.
-
Post Thanks / Like - 2 Thanks, 1 Likes, 0 Dislikes
----
-
Totally agree with droid1988. Just keep it simple. Recipes
----
-
Ha I would love to brew. I havnt found a good source for powder that I trust. And I would love to stay away from I international ordering. Any suggestions would be appreciated. I would love nothing more that to brew 200ml of test OH Ya!!!
“I COMMAND YOU TO GROW!!!”
----
-
Originally Posted by
Boxsquatter
Ha I would love to brew. I havnt found a good source for powder that I trust. And I would love to stay away from I international ordering. Any suggestions would be appreciated. I would love nothing more that to brew 200ml of test OH Ya!!!
I fully understand you bro. Not feeling comfortable ordering from most of them.
----
-
Yeah it’s hard to find a gtg raw source. Some really are good but they don’t test what they carry. So it’s really hard to know what you get is what you asked for.
----
-
Bro their are plenty. But if you google that shot you will find dozens of awesome and easy brewing g methods. Right down to the amounts of each product you need and I even found one on your tube with a video tutorial.
“I COMMAND YOU TO GROW!!!”
----
-
Bass killer has a calculator that helps out with brewing. Check it out.
-
Post Thanks / Like - 1 Thanks, 1 Likes, 0 Dislikes
----
-
Many recipes are just regurgitated, and far too high in BA and BB.
Some brewers actually start low percentages, and add BB until it holds in varying condition. They get the consistency they desire and did not rely on regurgitated recipes. Will those recipes work, sure... but again, far too high in BA and BB.
Some compounds it is common knowledge that very low percentages of BA and BB can be used.
There are Test E 250mg/ml and even @ 300mg/ml that call for 2%BA and 20%BB... that is ridiculous.
You don't even need BB in Test E @300mg/ml... but it will not be a viscous/thin as many would like.
I brew all my gear in MCT oil with low percentages.
My Test E and Deca I recently brewed, both at 300mg/ml, used 1%BA and 5%BB.
Before pinning I drop the vials in hot water in the sink about 3/4 way up the vial. Swab the tops and take a shower.
Get out shower, removed vials from hot bath, dry off...
Swab area to be injected.... and draw and pin with 1" 25G with ease.
The BB was added to thin it out enough to my liking.
I can even draw with a slin pin 29G, about 0.5ml in 45 seconds.
I get my raws from a source on this board... international, no problems. Everything thus far potent and gtg.
This board is very strict on sources... and runs a tight ship.
Last edited by Plate Smacker; 06-27-2018 at 09:46 PM.
"It's a lot of hard work, it's hard work that most people don't realize. I think the consistency of the hard work, is the hardest part." Dallas McCarver
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 Dislikes
----
-
Originally Posted by
Plate Smacker
Many recipes are just regurgitated, and far too high in BA and BB.
Some brewers actually start low percentages, and add BB until it holds in varying condition. They get the consistency they desire and did not rely on regurgitated recipes. Will those recipes work, sure... but again, far too high in BA and BB.
Some compounds it is common knowledge that very low percentages of BA and BB can be used.
There are Test E 250mg/ml and even @ 300mg/ml that call for 2%BA and 20%BB... that is ridiculous.
You don't even need BB in Test E @300mg/ml... but it will not be a viscous/thin as many would like.
I brew all my gear in MCT oil with low percentages.
My Test E and Deca I recently brewed, both at 300mg/ml, used 1%BA and 5%BB.
Before pinning I drop the vials in hot water in the sink about 3/4 way up the vial. Swab the tops and take a shower.
Get out shower, removed vials from hot bath, dry off...
Swab area to be injected.... and draw and pin with 1" 25G with ease.
The BB was added to thin it out enough to my liking.
I can even draw with a slin pin 29G, about 0.5ml in 45 seconds.
I get my raws from a source on this board... international, no problems. Everything thus far potent and gtg.
This board is very strict on sources... and runs a tight ship.
Have you brewed test base with MCT as carrier?
----
Bookmarks