Thread: Rookie makes his first brew of Test-E 300

you can go with low bb like %5

Originally Posted by Indahood

you can go with low bb like %5

So when heating the mix, do you start with some of the carrier oil? 5% isn’t enough to met it all


Sent from my iPhone using Tapatalk

My last brew was 250mg/ml @ %2 ba %5 bb and sesame oil, I mix ba and bb first then mix this with raws for 10 mins and last step I mix 60C degree oil with them again mixing for 10 mins.

It was painless good, oil was a bit thick but nothing to worry.

Also did Test P 100m @%2 ba and %15 bb it was pain in the ass. I feel pip 4 hours after injection. Pip peaks 12. hour and then starts to go away. All this takes 55 hours.
Oil looks pretty clean no crystals inside, I dont know if I am allergic to bb or %15 bb isn't enough for TP. or will it take time to get used to prop. I will see

Originally Posted by Indahood

My last brew was 250mg/ml @ %2 ba %5 bb and sesame oil, I mix ba and bb first then mix this with raws for 10 mins and last step I mix 60C degree oil with them again mixing for 10 mins.

It was painless good, oil was a bit thick but nothing to worry.

Also did Test P 100m @%2 ba and %15 bb it was pain in the ass. I feel pip 4 hours after injection. Pip peaks 12. hour and then starts to go away. All this takes 55 hours.
Oil looks pretty clean no crystals inside, I dont know if I am allergic to bb or %15 bb isn't enough for TP. or will it take time to get used to prop. I will see

Test-p sucks, I’ve got 20g of it to mix this weekend. I’m glad it was free and yes it always hurts. My tren didn’t turn out so well. Even though it’s clean and clear, PIP was strong for a day. After I get it tested for purity I’ll know more.


Sent from my iPhone using Tapatalk

Originally Posted by Caustic Charm

Test-p sucks, I’ve got 20g of it to mix this weekend. I’m glad it was free and yes it always hurts. My tren didn’t turn out so well. Even though it’s clean and clear, PIP was strong for a day. After I get it tested for purity I’ll know more.


Sent from my iPhone using Tapatalk

Yea also the same pip I have from tren ace, and little pip from tren e. Which source you used for raws could you pm me

Originally Posted by korsaire

this is a recipe from Rmewrench and that guy know is shit about brewing

If you want smooth prop, follow this to a t. Calculate carrier oil needed, add compound to carrier oil into beaker.
Put beaker in vat of water, put on stove and heat. You want to get your solution to atleast 200 degrees f. Use and infared temp gun
to measure temp. Heat for at least 30 minutes. Let cool add solvents, ba and bb. Filter and enjoy.
Its important to add solvents after it has cooled. If you add them before they will evaporate during heating.

some says first add solvents to the raw and others say first add oil... Which one is better?

Originally Posted by korsaire

this is a recipe from Rmewrench and that guy know is shit about brewing

If you want smooth prop, follow this to a t. Calculate carrier oil needed, add compound to carrier oil into beaker.
Put beaker in vat of water, put on stove and heat. You want to get your solution to atleast 200 degrees f. Use and infared temp gun
to measure temp. Heat for at least 30 minutes. Let cool add solvents, ba and bb. Filter and enjoy.
Its important to add solvents after it has cooled. If you add them before they will evaporate during heating.

So heat the oil and the raw first, let cool, then add solvent?


Sent from my iPhone using Tapatalk

Originally Posted by korsaire

in that recipes the reason you had add solvent after is because you heat to solution to 200 f and since ba and bb are solvent they will evaporate if you heat theme for that long so yes you let it cool and add solvent just like it is said in the post i have made

Much obliged, korsaire