-
I use 1%BA and 5%BB in MCT oil for both Test E 300 and Deca 300.
You can vial it.
10% overdose is fine.
My process for Test E into sealed sterile vials.
(Same process for Tren Ace, just different temperatures)
"added powder to beaker.
Added BB and stirred. Let sit 10 minutes then stirred again.
Added all MCT oil room temp.
Stirred and let sit 1 hour.
Stirred again and added to hotplate(old rice cooker)
Left on warm setting contantly stirring until brought up to 180F.
Take off hotplate and continue to stir until temp dropped to 130F.
Add BA.
Stir until temp drops to 105F.
Filter by pumping to 10in/Hg.
As it filters slowly drops vacuum to 5in/Hg.
Repump to 10in/Hg.
Filtering took about 15 minutes.
To get out most of remaining oil, pump to 10in/Hg..
Walk away, it will slowly lose all vacuum. Repump.
Do this a couple times.
Some will go to the gods. Maybe 1/2ml. (greedy bastards)
Remove bottle top filter.
Place lid on media bottle.
This next part may seem sketchy, but it's fine.
I have a big Honeywell air purifier I have running in the bathroom prior. Everything is wiped down. No rugs, hardwood floor.
The purifier if off during brewing and transfer.
I wear these gym clothes that are silky, so less chance of fibers coming off clothes.
I take a 60ml syringe, put on 20G 1"needle...pull plunger back ready to remove. Unscrew cap to where it is just sitting on top of media bottle. I hold syringe with outsteetched arms and pull out plunger, remove lid from media bottle and pour/backfill 60ml syringe, put lid back on media bottle, put plunger in syringe slightly, then hold syringe needle up so air is at top and push plunger all the way in to seat it.
I use 24G needle to vent sterile sealed vials that were swabbed.
I then dispense into vials.
Now, I need to refill syringe.
There will be slight amount of drops lost from needle drippage.
I inspect my vials with light and have never seen any contamination such as body hair or skin, other(I shave my head bald and trim body hair regularly).
I fill the bathtub up with many bottles of Nair Hair Removal, put tape on my eyebrows, and lay in the tub fully submerged and breathe with a snorkeling tube...jk bro lol.
We are talking about 3 seconds where the oil meets outside air into syringe. Yes, not most sanitary because I am not wearing a full body suit used to capture ET and his pals.
Last edited by Plate Smacker; 08-18-2018 at 04:20 AM.
"It's a lot of hard work, it's hard work that most people don't realize. I think the consistency of the hard work, is the hardest part." Dallas McCarver
-
Post Thanks / Like - 1 Thanks, 1 Likes, 0 Dislikes
----
-
Originally Posted by
Plate Smacker
I use 1%BA and 5%BB in MCT oil for both Test E 300 and Deca 300.
You can vial it.
10% overdose is fine.
My process for Test E into sealed sterile vials.
(Same process for Tren Ace, just different temperatures)
"added powder to beaker.
Added BB and stirred. Let sit 10 minutes then stirred again.
Added all MCT oil room temp.
Stirred and let sit 1 hour.
Stirred again and added to hotplate(old rice cooker)
Left on warm setting contantly stirring until brought up to 180F.
Take off hotplate and continue to stir until temp dropped to 130F.
Add BA.
Stir until temp drops to 105F.
Filter by pumping to 10in/Hg.
As it filters slowly drops vacuum to 5in/Hg.
Repump to 10in/Hg.
Filtering took about 15 minutes.
To get out most of remaining oil, pump to 10in/Hg..
Walk away, it will slowly lose all vacuum. Repump.
Do this a couple times.
Some will go to the gods. Maybe 1/2ml. (greedy bastards)
Remove bottle top filter.
Place lid on media bottle.
This next part may seem sketchy, but it's fine.
I have a big Honeywell air purifier I have running in the bathroom prior. Everything is wiped down. No rugs, hardwood floor.
The purifier if off during brewing and transfer.
I wear these gym clothes that are silky, so less chance of fibers coming off clothes.
I take a 60ml syringe, put on 20G 1"needle...pull plunger back ready to remove. Unscrew cap to where it is just sitting on top of media bottle. I hold syringe with outsteetched arms and pull out plunger, remove lid from media bottle and pour/backfill 60ml syringe, put lid back on media bottle, put plunger in syringe slightly, then hold syringe needle up so air is at top and push plunger all the way in to seat it.
I use 24G needle to vent sterile sealed vials that were swabbed.
I then dispense into vials.
Now, I need to refill syringe.
There will be slight amount of drops lost from needle drippage.
I inspect my vials with light and have never seen any contamination such as body hair or skin, other(I shave my head bald and trim body hair regularly).
I fill the bathtub up with many bottles of Nair Hair Removal, put tape on my eyebrows, and lay in the tub fully submerged and breathe with a snorkeling tube...jk bro lol.
We are talking about 3 seconds where the oil meets outside air into syringe. Yes, not most sanitary because I am not wearing a full body suit used to capture ET and his pals.
I can’t believe how much we have in common on the process, even though your steps are different. I use 60 ml syringe with stainless steel blunt tip loaders. My vials are sterilized in the oven at 250 for 30 minutes, or I used the pressure cooker for anything less than 10 bottles. I have a webeon (sp?) air purifier, 5 stage. It runs for 60 minutes before the lab work. Alcohol and bleach wipe downs to the whole area.
Sunday is my next batch, but I also have about 40g of test-e and 20g of test-p to do. Fun times learning all this, my thanks to everyone that’s sharing the knowledge.
Sent from my iPhone using Tapatalk
----
Bookmarks