Hey guys after weeks of research and development through the web and the BOP forum I finally did my first brew.
AAS Raws-
From Purple Panda Labs (International)
Shipping took approximately 4 weeks due to a 4 day delay (post office error)
*I won't discuss how they packaged it but it was creative*
- 100g Test E
- 30g Tren E
- 30g Deca
SETUP-
I decided to brew in the kitchen, sanitized the hell out of the stovetop, counters, everything.
I used a brand new black garbage bag to cover my counter and taped it down.
I layed out my materials and equipment ensuring i used gloves when touching anything.
I sterilized all beakers, flasks, and vials.
RECIPE-
Test E 300mg 2% BA, 10% BB, GSO (10% overdose)
Deca 300mg 2% BA, 10% BB, GSO (10% overdose)
Tren E 300mg 2% BA, 18% BB, GSO (10% overdose)
PROCEDURE-
Started with Test E
-Weighed raw powder and put it into the beaker
-Measured the BA, BB, & GSO then added it to the beaker
-Put 3 inches of water into a sauce pan brought it to a boil and put the beaker into the water stirring occasionally
-Once it reached 200 degrees I let it sit at that temp for 25 minutes
-After the 25 minutes I let the solution cool below 120 and began to filter
-The filter cracked because of too much pressure from the hand pump, I saved the solution using a beaker and moved on to the Deca (After brewing and bottling the Deca and Tren E i re-filtered the Test E)
Deca next
-Same procedure as above except i used less pressure during filtration
-Bottling and capping went smooth (Vials were pre-labeled and sterilized)
Tren E
-Carrier oil was brought to 200 degrees in a beaker alone
-A second beaker was used to mix the raw powder, BA, and BB
-Mixed the second beaker while in the sauce pan for 20 second until it was clear as honey then removed from the sauce pan
-I brought the carrier oil down in temp to 160 degrees and combined it with the 2nd beaker
-I mixed the solution for a few minutes and began to filter, bottle, and cap.
Back to the Test E
-I refiltered the solution, bottled it and capped it
***TREN ERROR**
-As I was finishing with bottling the Test E I noticed the Tren crashed!!! WTF I used 18% BB!
-House temp was mid 70's
-I reheated every Tren bottle and shook them until it was clear again
-I left all bottles out overnight to see if they would hold
-ALL BOTTLES INCLUDING THE TREN HELD JUST FINE
LESSON LEARNED- AFTER HEATING THE CARRIER OIL AT 200 DEGREES FOR 25 MINS, BRING THE TEMP DOWN TO 160 DEGREES, ADD THE SOLUTION (WITH THE AAS, BA, & BB) TO THE CARRIER OIL AND KEEP IT AT THAT TEMP FOR 20 MINUTES, THEN COOL DOWN AND BEGIN FILTERING. I BELIEVE THIS WAS MY MISTAKE.
KEY NOTES
- ALL 3 COMPOUNDS WERE CLEAR AFTER BREWING, NO CLOUDINESS, PRIOR TO FILTRATION
- ALL 3 COMPOUNDS WERE CLEAR AGAIN AFTER FILTRATION AND BOTTLING
- SCREW PLASTIC FILTERS I'M GETTING SOME GLASS
- BESIDES THE TREN CRASH AND THE FILTER CRACKING WITH THE TEST NO OTHER ERRORS OCCURRED
- AFTER HEATING AND SHAKING THE TREN THEY NEVER CRASHED AGAIN
- THE NEXT DAY I PINNED AND HAD ZERO PIP, IT WAS SMOOTH AS BUTTER, I DID NOT HEAT VIALS PRIOR TO PINNING I PINNED AT ROOM TEMP
- CALCULATOR USED FOR EXACT AMOUNTS OF POWDER, OIL, AND SOLVENTS CAN BE FOUND ON THE PURPLE PANDA LABS WEBSITE
- PIN AMOUNTS WERE
- .5CC OF TEST E 300
- .5CC OF DECA 300
- 1CC OF TREN E 300
***ALL COMMENTS, ADVICE, AND/OR CRITIQUE WELCOME I'M HERE TO LEARN***
Bookmarks