1st Homebrew Test E 300, Tren E 300, Deca 300 (Review)

**RISK0451** · 10-11-2018, 12:43 AM

Hey guys after weeks of research and development through the web and the BOP forum I finally did my first brew.

AAS Raws-
From Purple Panda Labs (International)
Shipping took approximately 4 weeks due to a 4 day delay (post office error)
*I won't discuss how they packaged it but it was creative*
- 100g Test E
- 30g Tren E
- 30g Deca

SETUP-
I decided to brew in the kitchen, sanitized the hell out of the stovetop, counters, everything.
I used a brand new black garbage bag to cover my counter and taped it down.
I layed out my materials and equipment ensuring i used gloves when touching anything.
I sterilized all beakers, flasks, and vials.

RECIPE-
Test E 300mg 2% BA, 10% BB, GSO (10% overdose)
Deca 300mg 2% BA, 10% BB, GSO (10% overdose)
Tren E 300mg 2% BA, 18% BB, GSO (10% overdose)

PROCEDURE-
Started with Test E
-Weighed raw powder and put it into the beaker
-Measured the BA, BB, & GSO then added it to the beaker
-Put 3 inches of water into a sauce pan brought it to a boil and put the beaker into the water stirring occasionally
-Once it reached 200 degrees I let it sit at that temp for 25 minutes
-After the 25 minutes I let the solution cool below 120 and began to filter
-The filter cracked because of too much pressure from the hand pump, I saved the solution using a beaker and moved on to the Deca (After brewing and bottling the Deca and Tren E i re-filtered the Test E)

Deca next
-Same procedure as above except i used less pressure during filtration
-Bottling and capping went smooth (Vials were pre-labeled and sterilized)

Tren E
-Carrier oil was brought to 200 degrees in a beaker alone
-A second beaker was used to mix the raw powder, BA, and BB
-Mixed the second beaker while in the sauce pan for 20 second until it was clear as honey then removed from the sauce pan
-I brought the carrier oil down in temp to 160 degrees and combined it with the 2nd beaker
-I mixed the solution for a few minutes and began to filter, bottle, and cap.

Back to the Test E
-I refiltered the solution, bottled it and capped it

***TREN ERROR**
-As I was finishing with bottling the Test E I noticed the Tren crashed!!! WTF I used 18% BB!
-House temp was mid 70's
-I reheated every Tren bottle and shook them until it was clear again
-I left all bottles out overnight to see if they would hold
-ALL BOTTLES INCLUDING THE TREN HELD JUST FINE

LESSON LEARNED- AFTER HEATING THE CARRIER OIL AT 200 DEGREES FOR 25 MINS, BRING THE TEMP DOWN TO 160 DEGREES, ADD THE SOLUTION (WITH THE AAS, BA, & BB) TO THE CARRIER OIL AND KEEP IT AT THAT TEMP FOR 20 MINUTES, THEN COOL DOWN AND BEGIN FILTERING. I BELIEVE THIS WAS MY MISTAKE.

KEY NOTES

ALL 3 COMPOUNDS WERE CLEAR AFTER BREWING, NO CLOUDINESS, PRIOR TO FILTRATION
ALL 3 COMPOUNDS WERE CLEAR AGAIN AFTER FILTRATION AND BOTTLING
SCREW PLASTIC FILTERS I'M GETTING SOME GLASS
BESIDES THE TREN CRASH AND THE FILTER CRACKING WITH THE TEST NO OTHER ERRORS OCCURRED
AFTER HEATING AND SHAKING THE TREN THEY NEVER CRASHED AGAIN
THE NEXT DAY I PINNED AND HAD ZERO PIP, IT WAS SMOOTH AS BUTTER, I DID NOT HEAT VIALS PRIOR TO PINNING I PINNED AT ROOM TEMP
CALCULATOR USED FOR EXACT AMOUNTS OF POWDER, OIL, AND SOLVENTS CAN BE FOUND ON THE PURPLE PANDA LABS WEBSITE
PIN AMOUNTS WERE