-
Test cyp random crashes
Everything else I brew i never have any issue with. I have read a lot of good advice on here about different ways to brew test cyp but I always have random vials crash. I have used up to 16% BB and as low as 12% BB. If I brew lets say 20 vials sometimes I will have 3 crash and the rest are fine, sometimes its almost half. I put my powder in the same beaker with the oil, bb, and ba mix and then place on hot plate until it is nice and clear. Would changing my order of operations help? For example, melting the powder alone and then adding oil, bb, ba? I cant really see how this would change anything. I use 2% ba with all batches and I just would like to make the cyp without going over 14-15% bb otherwise the pip is to much. As always any advice will always be appreciated brothers.
-
Post Thanks / Like - 1 Thanks, 1 Likes, 0 Dislikes
----
-
Originally Posted by
Leoterelli250
Everything else I brew i never have any issue with. I have read a lot of good advice on here about different ways to brew test cyp but I always have random vials crash. I have used up to 16% BB and as low as 12% BB. If I brew lets say 20 vials sometimes I will have 3 crash and the rest are fine, sometimes its almost half. I put my powder in the same beaker with the oil, bb, and ba mix and then place on hot plate until it is nice and clear. Would changing my order of operations help? For example, melting the powder alone and then adding oil, bb, ba? I cant really see how this would change anything. I use 2% ba with all batches and I just would like to make the cyp without going over 14-15% bb otherwise the pip is to much. As always any advice will always be appreciated brothers.
One word........
Migyol 840. It’s expensive as all hell but it will hold anything. I use it to brew my oral steroids into injectable oil based versions I can hold tren base anadrol and dianabol all in the same vial without it crashing with mig.
Again it’s stupid expensive but worth it iv brewed 600mg test enth and it held fine for moths and still showed no signs of wanting to crash. The best one was I brewed dbol at 100mg/ml and put it in the freezer for hours and guess what. ...it did not crash
Sent from my iPhone using Tapatalk
----
-
This looks interesting thank you I appreciate it. May I ask is the viscosity of Migyol 840 less than grape seed or other commonly used oils? Pretty much is it not as thick and does it cause pip? I will obviously be looking this up but not sure if you knew off hand. Thanks again brother.
-
Post Thanks / Like - 1 Thanks, 1 Likes, 0 Dislikes
----
-
The only way I've gotten my test-c not to crash using mct oil and using 2%BA and 18%BB any less BB and it crashes.
----
-
Also not sure if I am allowed to ask but is there a specific place you like to order from that you know is legit?
----
-
Originally Posted by
Leoterelli250
This looks interesting thank you I appreciate it. May I ask is the viscosity of Migyol 840 less than grape seed or other commonly used oils? Pretty much is it not as thick and does it cause pip? I will obviously be looking this up but not sure if you knew off hand. Thanks again brother.
It’s thick but once you heat it up and add everything it’s silky smooth. It goes through a watman syringe filter like water once finished.
Sent from my iPhone using Tapatalk
----
-
18%bb 2% ba never had 1 issue
----
-
Originally Posted by
Leoterelli250
Everything else I brew i never have any issue with. I have read a lot of good advice on here about different ways to brew test cyp but I always have random vials crash. I have used up to 16% BB and as low as 12% BB. If I brew lets say 20 vials sometimes I will have 3 crash and the rest are fine, sometimes its almost half. I put my powder in the same beaker with the oil, bb, and ba mix and then place on hot plate until it is nice and clear. Would changing my order of operations help? For example, melting the powder alone and then adding oil, bb, ba? I cant really see how this would change anything. I use 2% ba with all batches and I just would like to make the cyp without going over 14-15% bb otherwise the pip is to much. As always any advice will always be appreciated brothers.
I would not recommend you trying to melt test cyp first. Applying a lot of heat is just bad practice in general. Hot tapwater in a pot is enough and just have patience.
Applying heat when you're brewing won't lessen the chance of your gear crashing in the future.
You either did something wrong or you're storing the vials in a cold place. There is also the possibility that it wasn't mixed together properly.
----
-
Originally Posted by
Leoterelli250
Everything else I brew i never have any issue with. I have read a lot of good advice on here about different ways to brew test cyp but I always have random vials crash. I have used up to 16% BB and as low as 12% BB. If I brew lets say 20 vials sometimes I will have 3 crash and the rest are fine, sometimes its almost half. I put my powder in the same beaker with the oil, bb, and ba mix and then place on hot plate until it is nice and clear. Would changing my order of operations help? For example, melting the powder alone and then adding oil, bb, ba? I cant really see how this would change anything. I use 2% ba with all batches and I just would like to make the cyp without going over 14-15% bb otherwise the pip is to much. As always any advice will always be appreciated brothers.
Test cyp is known to crash to this day out of 50 vials id say 2 percent crash
----
-
Originally Posted by
Leoterelli250
This looks interesting thank you I appreciate it. May I ask is the viscosity of Migyol 840 less than grape seed or other commonly used oils? Pretty much is it not as thick and does it cause pip? I will obviously be looking this up but not sure if you knew off hand. Thanks again brother.
All we use is migyol oil best oil on the planet smooth no pip super easy on loading people love it
-
Post Thanks / Like - 1 Thanks, 1 Likes, 0 Dislikes
----
Bookmarks