-
Process review
Hi guys. I just received my first order (bold undec and test e) and will brew them soon at 200mg/ml for both just to be safe. Before doing it I would like to check if my whole progress is fine or need minor fixes, so all suggestions are appreciated.
Steps:
1) Wash becker using soapy water, dry, clean with 70% alcohol and dry again using paper towel.
2) Weigh the powder
3) Add BB and GSO (both USP) using standard syringes (sizes depending on batch size)
4) Heat up to ~80ºC using bain marie method for 25~30mins stirring the whole time using a syringe. (I need some help here in order to avoid moisture in the becker)
5) Let it cool for a couple of minutes
6) Add BA and stir a little bit
6) Filter using 0,22 pvdf syringe filter
7) Wait 2-3 days to check if its going to crash or not
Note: Im using BB/BA at 20/2
Thank you very much
Zanqueta
PS: English is not my mother language, sorry about any mistakes.
Last edited by Zanqueta; 09-27-2019 at 01:44 AM.
----
-
----
-
-
Post Thanks / Like - 1 Thanks, 1 Likes, 0 Dislikes
----
-
Russianbot is a Brew master in sure he’ll chime
In when he see this.
Sent from my iPhone using Tapatalk
-
Post Thanks / Like - 2 Thanks, 1 Likes, 0 Dislikes
----
-
Your on the right path brother. Only things I'd do differently is take the test-e to over 200f degrees for 10min or so to get the acid out that's used in manufacturing
Also if your going to wait to see if it crashes do that before you filter and bottle not before just leave it in the beaker and cover it up with syran wrap or put it into a sterile media vile. Wait a couple days then heat it to 100f then filter and bottle
Also I'd add the ba at around 140-160f and maintain that temp for 20min stirring constantly.
With 2% bA and 20% BB. You can easily go test-e 300mg/ml and eq up to 500mg/ml
Also if you plan on brewing more in the future I'd recommend getting yourself a good magnetic stirrer hot plate. It will make your life alot easier
Last edited by Yellowninja; 09-28-2019 at 01:12 PM.
-
Post Thanks / Like - 2 Thanks, 3 Likes, 0 Dislikes
----
-
Originally Posted by
Yellowninja
Your on the right path brother. Only things I'd do differently is take the test-e to over 200f degrees for 10min or so to get the acid out that's used in manufacturing
Also if your going to wait to see if it crashes do that before you filter and bottle not before just leave it in the beaker and cover it up with syran wrap or put it into a sterile media vile. Wait a couple days then heat it to 100f then filter and bottle
Also I'd add the ba at around 140-160f and maintain that temp for 20min stirring constantly.
With 2% bA and 20% BB. You can easily go test-e 300mg/ml and eq up to 500mg/ml
Also if you plan on brewing more in the future I'd recommend getting yourself a good magnetic stirrer hot plate. It will make your life alot easier
thank you very much for ur answer, my friend.
1- So it's better if i heat the test e to 200f and not EQ?Do i heat EQ to 80C as i said or i go over that?? Would 200f hurt the test e?
2- About ba/bb: since this is my first time brewing id like to avoid any kind of issues at this part and i see many experienced people brewing their things using 20/2 with no pip, but after 2-3 times doing it i will certainly stick to 10-15/2.
3-Yea, i know magnetic stirrer hot plate are magic and i will buy one after sometime.
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Dislikes
Mesus thanked for this post
----
-
When the sponsor forums are back up and running I have alot of step by step procedures for my brews in the anabolic-hormones forum
-
Post Thanks / Like - 2 Thanks, 2 Likes, 0 Dislikes
----
-
You only need to heat the test- e to 200 Fahrenheit no it wont hurt it. The eq is fine to brew in the 140-160 farenheit range
I use 2% ba and 20% bb on almost all of my brews now the only exception is on preworkouts I use more bb
-
Post Thanks / Like - 2 Thanks, 1 Likes, 0 Dislikes
----
-
Finally could homebrew my test e and EQ at 200mg/ml as I said. Heated the test e at around 200-203°F for 25 mins and Eq at 180 for 10 mins and I will let it sit for a few days before filtering, but i realized there are a few drops inside both beckers. Im sure that the ones in EQ are water because they are a little bigger, but the ones in Test E becker (image below) are tiny, so idk if its water or some other things. Do you think its water? Do you think i will have problems with moisture in a few days? What should I do if that happens?
Other than that the oils are fine, crystal clear.
WhatsApp Image 2019-10-19 at 12.54.28.jpeg
----
-
How does one get water into an oil based brew?
----
Reply With Quote
Bookmarks