-
Originally Posted by
FastTrack
Testosterone Enanthate
Test E is soluable in oil alone. It needs no additional solvents, but for antimicrobial puposes BA (benzyl alcohol) is used.
Items Needed for a 10 gram conversion:
10 grams test enanthate
0.80ml benzyl alcohol (2% BA)
31.20ml oil
Syringes 3cc & 5cc or 10cc
20 gauge needles
Mixing vial (or preferably beaker)
Sterile vial
Sterile syringe filter
Weigh out 10 grams of hormone into mixing vial or beaker.
Add benzyl alcohol and 26.20cc of oil. (This will leave 5cc oil for later.)
Place on stovetop (electric stove) or frying pan (gas stove) on medium high heat.
Swirl and heat until solution is completely homogeneous and clear. NO hormone "swirls" or visible separation should be left.
Place 20g needle in sterile vial and attach syringe filter.
Place another needle through stopper to relieve pressure
Draw out hormone solution with 5 or 10cc syringe and run it through the syringe filter until all solution is filtered.
Run the addition 5cc of saved oil from step 2 through syringe filter to purge.
This conversion results in 40ml - 250mg/ml sterile solution for injection.
Ive been told without BB it will be way to thick. I need at least 10% BB to thin it out.
----
-
I usually run 20%bb. I know it's not needed, but it does help with thinning the solution out.
----
-
----
-
20% BB is what I have went by in the past as well... that information looks g2g though. You can also try putting it INSIDE the oven so you can set the temp on a specific number. 275 degrees is what I used I believe.
----
-
The oven thermostats are very inconsistent, also the radiant heat doesn't hear it thoroughly, it can also damage the hormone. It's the wrong kind of heat. If your brewing it needs to be evenly heated through convection from the bottom of the oil. The warmer thinner oil will rotate to the top as the ever oil falls. It will heat evenly like that. If ur talking about baking final product it will still b improper. Needs an autoclave.
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Dislikes
----
-
10g should yield 40ml at 250mg/ml.
20% BB = 8ml
2% BA = 0.8ml
Raw powder: 10g x 0.9 = 9ml (10g of test e displaces 9ml in solution form)
Carrier Oil = 22.2ml (remember to leave out 2ml to use in the end to clean out syringe filter)
Have any questions pm me.
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Dislikes
----
-
Originally Posted by
4everstrong
Ive been told without BB it will be way to thick. I need at least 10% BB to thin it out.
I always use BB. 10% with Test E. IMO, 20% is way too high. It wont hurt you, but you could use all that extra BB on your next brew.
----
-
Originally Posted by
hijacked
I always use BB. 10% with Test E. IMO, 20% is way too high. It wont hurt you, but you could use all that extra BB on your next brew.
I agree 20% is way to much for Test E. im either going to use 10% or 15% bc i want it to flow through a 25g needle.
----
-
Originally Posted by
4everstrong
I agree 20% is way to much for Test E. im either going to use 10% or 15% bc i want it to flow through a 25g needle.
20 bb sure would be smooth tho right?
----
-
Yeah but it would flow through a 25g just fine at 10-15%
----
Bookmarks