-
Is this correct guys?
Im going to brew 10grams of test E 250mg/ml 40ml of Test E
I figured it up on the calculator and it said i need 23.50 of oil but in another thread i read where you need 25.50? Is this bc you need 2ml at the end of the brew to push through the whatman filter and get gear out?
So i put .80ml Ba and 7.20 BB in a beaker. and then put the beaker on the stove in a pan of water and stir and let the powder melt? And then i add 23.50 of grapeseed oil. and then let it cool for 5 mins. Then filter the gear. Then once all of the gear is in a sealed sterile vial. Take 2ml of grapeseed oil and run it through the whatman filter?
Is this correct.
Thanks.
----
-
Looks good but I'm checking a reference to be 100% ..stay tuned
----
-
Originally Posted by
FastTrack
Looks good but I'm checking a reference to be 100% ..stay tuned
Okay thanks FastTrackI appreciate.
----
-
Testosterone Enanthate
Test E is soluable in oil alone. It needs no additional solvents, but for antimicrobial puposes BA (benzyl alcohol) is used.
Items Needed for a 10 gram conversion:
10 grams test enanthate
0.80ml benzyl alcohol (2% BA)
31.20ml oil
Syringes 3cc & 5cc or 10cc
20 gauge needles
Mixing vial (or preferably beaker)
Sterile vial
Sterile syringe filter
Weigh out 10 grams of hormone into mixing vial or beaker.
Add benzyl alcohol and 26.20cc of oil. (This will leave 5cc oil for later.)
Place on stovetop (electric stove) or frying pan (gas stove) on medium high heat.
Swirl and heat until solution is completely homogeneous and clear. NO hormone "swirls" or visible separation should be left.
Place 20g needle in sterile vial and attach syringe filter.
Place another needle through stopper to relieve pressure
Draw out hormone solution with 5 or 10cc syringe and run it through the syringe filter until all solution is filtered.
Run the addition 5cc of saved oil from step 2 through syringe filter to purge.
This conversion results in 40ml - 250mg/ml sterile solution for injection.
-
Post Thanks / Like - 1 Thanks, 1 Likes, 0 Dislikes
----
-
----
-
Originally Posted by
FastTrack
Testosterone Enanthate
Test E is soluable in oil alone. It needs no additional solvents, but for antimicrobial puposes BA (benzyl alcohol) is used.
Items Needed for a 10 gram conversion:
10 grams test enanthate
0.80ml benzyl alcohol (2% BA)
31.20ml oil
Syringes 3cc & 5cc or 10cc
20 gauge needles
Mixing vial (or preferably beaker)
Sterile vial
Sterile syringe filter
Weigh out 10 grams of hormone into mixing vial or beaker.
Add benzyl alcohol and 26.20cc of oil. (This will leave 5cc oil for later.)
Place on stovetop (electric stove) or frying pan (gas stove) on medium high heat.
Swirl and heat until solution is completely homogeneous and clear. NO hormone "swirls" or visible separation should be left.
Place 20g needle in sterile vial and attach syringe filter.
Place another needle through stopper to relieve pressure
Draw out hormone solution with 5 or 10cc syringe and run it through the syringe filter until all solution is filtered.
Run the addition 5cc of saved oil from step 2 through syringe filter to purge.
This conversion results in 40ml - 250mg/ml sterile solution for injection.
Holy crap! You can't ask for better then that for info damn.
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Dislikes
----
-
Originally Posted by
Greenegorilla2
Let us know how it goes.
I will! It will be about two weeks before i start.
----
-
Originally Posted by
JM750
Holy crap! You can't ask for better then that for info damn.
Thanks
----
-
----
-
I havnt got my powder yet bro. Im waiting for it to arrive.
----
Bookmarks